Gear Head College
http://gearheadcollege.org/

inverted fork rebuild
http://gearheadcollege.org/viewtopic.php?f=2&t=5
Page 1 of 1

Author:  super [ Wed Oct 22, 2008 4:20 pm ]
Post subject:  inverted fork rebuild

1. First, use a strap wrench to remove the swoopy seal cover. (See fig. 10 and 11)
2. Depending on model, use a spanner or hex wrench to remove phantom body cap. (Hex wrench with drilled hole for brake line available from American Susp.)
3. Pull steel braided line out.
4. Remove the bottom out.
5. Drain oil, cycle shock and remove Bottom-out spring, spring top, and push rod tube.
6. Clean and inspect all parts. Make sure NOTHING is damaged. Check your chrome.
7. Inner tube then goes into vise. Use a breaker bar to twist
8. Pull out lower leg, remove main spring, swoopy seal, and remove inner tube, with piston.
9. Use a pick to remove seal snap ring. Use screwdriver and hammer at end of seal to remove it. Wipe inside all clean to remove any debris.
10. Place new seal in with the numbers facing out; make sure seal bottoms out.
11. Install cir-clip, when you hear the snap, the clamp is fully in.
12. Use condom over inner tube so as not to cut the seal. Slide inner tube all the way in; push it down.
13. Pull swoopy cover seal over, first before installing leg.
14. Spring pointed down, with push rod tube on top, washer between spring and cir clamp.
15. Run brake line through inner tube. Make sure that it is COMPLETELY STRAIGHT so it does not knot up.
16. Use ‘242 Lock-Tite’ on lower leg threads once around tight and with 90 lbs. of torque.
17. Clean up all debris off of the brake line.
18. Slide in spring top with 3-inch spring.
19. Use 3/8 rod to even it out. Make sure push rod is over and down in.
20. Bottom out steel tube goes in next.
21. Put a loop in the brake line. Make sure you walk it the same way through and slide it part way down.
22. Place cir-clip around brake line. Brake line loop to go right under threads.
23. Fill fork with 5-weight oil. [For V8 cycles or +0 and below use 10 wt. oil]
24. Tape end of steel braided line. Dip it in Vaseline. Push it through body cap slowly and not to cut the seal.
25. Put on a table to cycle oil, ‘242 Lock-Tite’ seal cover; one drop hand tight.

Attachments:
rebuild a phantom.doc [22 KiB]
Downloaded 1663 times

Author:  super [ Wed Oct 22, 2008 4:28 pm ]
Post subject:  Re: inverted fork rebuild

see the picture for a breakdown

Attachments:
a_ExplodedB17.jpg
a_ExplodedB17.jpg [ 116.73 KiB | Viewed 16239 times ]

Author:  ironhead [ Sun Mar 15, 2009 4:21 pm ]
Post subject:  Re: inverted fork rebuild

Can you post pictures of "1. First, use a strap wrench to remove the swoopy seal cover. (See fig. 10 and 11)" Thanks

Author:  ironhead [ Sat Mar 21, 2009 3:53 pm ]
Post subject:  Re: inverted fork rebuild

In step 7 you put inner tube in vise and use breaker bar to twist, this step is to break lower leg loose?

Author:  joe [ Thu Mar 26, 2009 4:59 pm ]
Post subject:  Re: inverted fork rebuild

Yes, you need to seperate the axle clamp from the inner tube so that the inner tube may be slid past the bearings and seals.
In my opinion this is the only difficult part of a rebuild. the axle clamp is attached to the inner tube with 90 foot pounds of tourqe and lock tite.
If you let the inner tube slip in the vise, or you do not use soft jaws that grab around the inner tube you may dammage the inner tube. If the inner tube gets damaged the seals will probably be torn by the damaged inner tube. If you make the inner tube out of round the seal will not seal properly.
Use the proper clamp for the inner tube and you should have no problems.

Check this site for more pictures

http://www.garagegirls.tv/album/forks/

Page 1 of 1 All times are UTC - 8 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/